$TXT Created by CRUMLEY,JAMIE at DEVVLD.FO-ALBANY.MED.VA.GOV  (KIDS) on Tuesday, 10/30/12 at 15:24
=============================================================================
Run Date: FEB 12, 2013                     Designation: GMTS*2.7*96
Package : GMTS - HEALTH SUMMARY               Priority: EMERGENCY
Version : 2.7        SEQ #94                    Status: Released
                  Compliance Date: FEB 20, 2013
=============================================================================

Associated patches: (v)GMTS*2.7*47 <<= must be installed BEFORE `GMTS*2.7*96'

Subject: HEALTH SUMMARY SUPPORT FOR LAB RE-ENGINEERING

Category: 
  - Routine

Description:
============

 1. As a part of the Lab Re-engineering project, displays are being
 modified to show the Cerner COTS (Commercial Off-The-Shelf) accession
 number for those orders that are being performed on Cerner.
  
 One of these displays is controlled by the Health Summary v2.7 package. 
 The purpose of this patch is to modify the display on the Reports Tab - 
 Clinical Reports - Laboratory - Lab Orders to show the COTS accession 
 number if it is available. This was just a change to a Health Summary 
 routine, no components were involved.
  
 2. In some cases, the status of a test displays as 'COMPLETED' on the 
 Computerized Patient Record System (CPRS) Reports Tab and Lab Tab 
 displays, rather than the appropriate status of 'CANCELED'. This patch 
 corrects this problem.
  
 3. In support of New Service Request 20070438, a change is required in 
 the Health Summary package. This patch makes this change to the Lab 
 Display Status. The change will be dormant until CPRS v30 is installed.
  
 Associated Remedy:
 ==================
 N/A
  
 Associated NSR(s):
 ==================
 20070438
  
 Test Sites:
 ===========
 Huntington, WV
 Lexington, KY
 Salisbury, NC
  
 INSTALLATION INSTRUCTIONS:
 ==========================
  This patch should be loaded during non-peak hours to minimize disruption
  to users.  Installation will take less than 1 minute.  Users may remain
  on the system.
  
  1.  Use the INSTALL/CHECK MESSAGE option on the PackMan menu.
  
  2.  From the Kernel Installation and Distribution System Menu, select
      the Installation menu.
  
  3.  From this menu, you may elect to use the following options
      (when prompted for INSTALL NAME, enter GMTS*2.7*96):
          a.  Backup a Transport Global
          b.  Compare Transport Global to Current System
          c.  Verify Checksums in Transport Global
  
  4.  When prompted 'Want KIDS to INHIBIT LOGONs during the install? NO//'
      respond NO.
  
  5.  When prompted 'Want to DISABLE Scheduled Options, Menu Options, and
      Protocols? NO//', respond NO.

Routine Information:
====================
The second line of each of these routines now looks like:
 ;;2.7;Health Summary;**[Patch List]**;Oct 20, 1995;Build 9

The checksums below are new checksums, and
 can be checked with CHECK1^XTSUMBLD.

Routine Name: GMTSLROE
    Before: B11334514   After: B12396519  **9,28,47,96**
 
Routine list of preceding patches: 47

=============================================================================
User Information:
Entered By  : CRUMLEY,JAMIE                 Date Entered  : AUG 31, 2010
Completed By: NADEAU,MARCY MARCONI          Date Completed: FEB 12, 2013
Released By : SCHWARTZ,VIKIE                Date Released : FEB 12, 2013
=============================================================================


Packman Mail Message:
=====================

$END TXT